First, the scope of application of the water tank sterilizer:
1. Secondary water supply tank (pool), fire fighting pool sterilization and algae;
2. Secondary disinfection of water and water storage facilities;
3. Swimming pool and fountain disinfection;
4. Industrial circulating water sterilization and algae killing;
5. Disinfection and sterilization of water wells and small self-contained water sources.
Second, the product features of the water tank sterilizer:
1. The water tank sterilizer has a fast speed of sterilization and algae, and has a broad spectrum, which can kill all microorganisms.
2. The water tank sterilizer has no secondary pollution, and the disinfectant is reduced to O2 and H2O after disinfection.
3. The water tank sterilizer is completely disinfected and has no dead angle circulation diffusion treatment, and has a continuous disinfecting effect.
4. The water tank sterilizer is easy to install and does not need to damage the original water tank structure, just put it in the water tank.
5. The water tank sterilizer time setting is automatic, the working state is adjustable, and no special person is required to take care of it.
Third, the water tank sterilizer function:
In the rated volume of water, the tank sterilizer treatment effect is as follows:
1. Sterilization rate of water tank sterilizer: 99.9%
2. Alcohol killing rate of water tank sterilizer: 99.9%
3. The water tank sterilizer can degrade pesticides, remove residual chlorine and deodorize.
Fourth, the water tank sterilizer consists of:
The water tank sterilizer is a split structure, the main body is an ozone generator, and the auxiliary machine is a gas mixer.
The ozone generator is divided into two types: air-cooled and water-cooled. The air-cooled ozone line and the line can be directly turned on; the water-cooled type should be connected to the inlet and outlet pipes first.
Note: Do not operate without water to avoid water leakage and leakage.
Fifth, the installation of the water tank sterilizer:
1. The main unit should be installed at 10CM above the ground, 20CM away from the wall, and ventilated and dry.
2. During installation, the mixer connecting pipeline line enters from the upper port of the water tank. The intake pipe naturally forms no return water above the water surface, thus ensuring the normal operation of the ozone generator.
3. The main cabinet should be well grounded to prevent leakage and electric shock.
4. Do not touch the inside and outside of the generator with your hand when working, to prevent electric shock and injury.
5. Do not lay the power line in the main box, in order to prevent interference discharge and normal operation of components.
6. The water outlet hole of the water tank should have a venting hole to reduce the internal pressure of the water tank to prevent the water from returning to the O3 pipe due to excessive pressure.
7. The ozone generator should be placed in a dry and well ventilated place to prevent corrosion damage caused by moisture during long-term work. The ozone generator in the box is a high-voltage discharge component, which is strictly touched by hand when working.
Sixth, the maintenance of the water tank sterilizer:
1. If the ozone generator line control part is stopped, the automatic control switch can be turned on, charged for 6 seconds, click the “time controller†lower left button until “888†is displayed, and then the standard time is set according to the time (time) ), then set the on-off time to work properly. When working automatically, the dial button can be rotated in the automatic running position.
2. It is normal for the mixer to have weak mechanical noise during operation.
3. If the gas supply pipe returns to the water, open the drain valve or loosen the ozone outlet of the ozone generator to remove the accumulated water.
4. If some pipes or parts have slight air leakage, apply 703, 704, 705 high pressure glue.
5. If the air-cooled or semi-air-cooled axial flow fan is damaged, the same type of axial flow fan must be replaced to avoid affecting the normal operation of the equipment.
6. The water tank sterilizer is divided into two series of WTS-2A and WTS-2B internal and external water tank sterilizers because of the different installation positions.